水中硬度自動監測儀 SP510 Hardness Analyzer with Reagents
產品編號：
線上水質硬度監測儀SP510採用比色法測量，具自動校正功能，可即時連續監測。SP510線上水硬度分析儀可用於軟化器出水、鍋爐水質的硬度監測；準確的控制軟化器在有需要的時候進行再生，延長水質軟化保持時間，減少再生成本。
Maximize your softener cycle time and minimize your regeneration cost.
Immediately signal hardness breakthrough to activate regeneration. Makes your water softening system more efficient and less costly. Reliable, simple and accurate- with automated calibration. Continuous monitoring in "real time".
- “即時”連續監測，測量週期2分鐘
- 硬度過高時，系統發出警告信號，同時啟動再生程序
- 有效提升水質軟化系統效能
- 所需維護工作量低 : 每6 個月更換一次泵管
- 自動校正功能
- 性價比高，適合系統閉路反控
Measurement Method 量測方法 : Colorimetric 比色法
Range Hardness levels : 0.3, 1, 2, 5, 10, 20, 50, 100 ppm (expressed as mg/L CaCO3)
Maintenance Interval 維護間隔 : Standardize and replenish reagents every 2 months using EDTA or high-level sample
Replace pump tubes every 6 months
Certifications 認證 : NRTL certified to UL and CSA standards, and CE approved
關鍵字 : 水 硬度 監測, 水 硬度 測定, 水 硬度 分析 儀, water hardness analyzer, water hardness monitoring
Maximize your softener cycle time and minimize your regeneration cost.
Immediately signal hardness breakthrough to activate regeneration. Makes your water softening system more efficient and less costly. Reliable, simple and accurate- with automated calibration. Continuous monitoring in "real time".
- “即時”連續監測，測量週期2分鐘
- 硬度過高時，系統發出警告信號，同時啟動再生程序
- 有效提升水質軟化系統效能
- 所需維護工作量低 : 每6 個月更換一次泵管
- 自動校正功能
- 性價比高，適合系統閉路反控
Measurement Method 量測方法 : Colorimetric 比色法
Range Hardness levels : 0.3, 1, 2, 5, 10, 20, 50, 100 ppm (expressed as mg/L CaCO3)
Maintenance Interval 維護間隔 : Standardize and replenish reagents every 2 months using EDTA or high-level sample
Replace pump tubes every 6 months
Certifications 認證 : NRTL certified to UL and CSA standards, and CE approved
關鍵字 : 水 硬度 監測, 水 硬度 測定, 水 硬度 分析 儀, water hardness analyzer, water hardness monitoring
Continuous Hardness Detection
The Hach SP 510 Hardness Monitor continuously monitors water systems to provide an alarm when total hardness exceeds a pre-set limit (eight alarms are available). By performing an analysis every two minutes, the SP 510 monitor can establish an automatic or semi-automatic system for water softener regeneration in a variety of commercial or industrial applications.
Simple to Read and Use
The SP 510 monitor detects hardness breakthrough when the capacity of a water softener is exhausted, immediately signaling the need for regeneration. Alarm points are 0.3, 1, 2, 5, 10, 20, 50, and 100 ppm (expressed as mg/L of CaCO3) and are selected by using the appropriate model. LED indicators show a simple HARD or SOFT sample status. Use the monitor's built-in alarm relay to actuate an external annunciator.
Rugged, lightweight, and self-contained
The case of the SP 510 monitor is made of ABS plastic which is lightweight, corrosion-resistant, and shatterproof. This sealed case is IP62-rated and has a hinged door that for easy access to internal components. All electronic circuits are isolated from the hydraulics compartment. A large window allows inspection of both LED indicators and reagent supplies at a glance. Wall-mounting is easy with built-in brackets. The instrument is rated for 115/220 Vac, 50/60 Hz operation, with a switch for voltage selection.
Making Water Softening Systems Cost-efficient
The traditional method of determining softener regeneration cycles is based on calculation of the water volume that can pass through a softener before its capacity is exhausted. Many variables (temperature, flow rate, and condition of the exchange resin) can affect the accuracy of these calculations. A substantial safety margin is also generally included, which can result in waste of time and brine used for regeneration. The Hach SP 510 monitor can eliminate this guesswork. The softener is regenerated only when needed, based on accurate chemical analysis rather than estimated volume.
Low Maintenance Requirements
The SP 510 monitor is designed for continuous, unattended use. It is virtually maintenance-free, requiring only about 15 minutes every two months to replenish and standardize the reagents. Tubing in the pump system should be replaced at six-month intervals. Spare pump tubing is supplied with the monitor.